KOMPETENSI KEAHLIAN TEKNIK ELEKTRONIKA INDUSTRI
No Nama Peralatan Merk Tipe Harga Satuan
1 Analog Circuit Training Kit CHOIEO 66968305A 78.028.500
2 Digital Circuit Training Kit CHOIEO 66968305B 78.028.500
3 Programmable Logic Controller Training Set CHOIEO 66965101 112.602.000
4 Electro Pneumatic Training System CHOIEO 66971105 136.771.500
5 Advanced Electro Hydraulic Training System CHOIEO 66971206 240.619.500
Spesifikasi Merk Tipe Harga Satuan
TRAINING CONTENT CHOIEO 66968305A 78.028.500
Analog Electronics Part
• Usage of commonly used instrument
• Diode characteristic test
• Triode transistor input, output characteristics test
• Transistor single transistor amplifier
• Two-pole amplifier circuit
• Negative feedback amplifier circuit
• Emitter follower
• Field-effect tube amplifier circuit
• Differential amplification circuit
• RC sine wave oscillator
• LC sine wave oscillator
• Operational amplifier parameter testing
• Integrated operational amplifier proportional summation operational circuit
• Integrated operational amplifier integrating and differentiating circuit
• Integrated operational amplifier voltage comparator circuit
• Integrated operational amplifier waveform generator circuit
• Integrated operational amplifier active filter circuit
• Integrated power amplifier
• OTL power amplifier
• Integrated voltage stabilizer
• Series voltage stabilizing circuit
PRODUCT COMPOSITION
1. Dimension: 1500mm×700mm×1600mm (approx.)
2. Working power supply: 220V/50Hz
3. Safety protection: Current mode residual-current circuit breaker, voltage mode leakage protector
4. Training table: Steel and wood structure, iron spraying plastics, wearproof and fireproof panel, equipped with drawer and cabinet for the storage of tools and components. (or aluminum alloy structure optional)
5. Analog circuit experiment part:
(1). Adjustable DC stabilized power supply: 0~30V/1.5A continuously adjustable, automatic shifting, with automatic overload protection and self-recovery function.
(2). Fixed DC stabilized power supply: +5V/3A, ±12V/1A
(3). AC power supply: 18V, 9V, 3V, 0V
(4). Function signal generator: wave form (sine wave, triangular wave, square wave), frequency range: 5Hz~550KHz continuously adjustable, output amplitude: sine wave more than 0-10Vp-p
(5). Frequency meter: measurement range: 1Hz~8MHz, 6-bit digital display, automatic shifting, input impedance ≥1MΩ/20PF, sensitivity
Measuring meter:
(1). Voltmeter: DC200V, class 0.5
(2). Ammeter: DC200mA, class 0.5
(3). Digital multimeter
TRAINING CONTENT CHOIEO 66968305B 78.028.500
Digital Electronics Part
• Transistor switching characteristic, clipper and clamper
• Logic function and parameter testing of TTL integrated logic gate
• Logic function and parameter testing of COMS integrated logic gate
• Connection and driving of integrated logic circuit
• Combinational logic circuit experiment
• Decoder and its application
• Data selector and its application
• Trigger and its application
• Counter and its application
• Shifting register and its application
• Pulse distributor and its application
• Self-excited multivibrator
• Monostable trigger and schmitt trigger
• 555 time base circuit and its application
• D/A, A/D converter
• Electronic stopwatch
• Competition responder
• Tug of war game machine
PRODUCT COMPOSITION
1. Dimension: 1500mm×700mm×1600mm (approx.)
2. Working power supply: 220V/50Hz
3. Safety protection: Current mode residual-current circuit breaker, voltage mode leakage protector
4. Training table: Steel and wood structure, iron spraying plastics, wearproof and fireproof panel, equipped with drawer and cabinet for the storage of tools and components. (or aluminum alloy structure optional)
Digital circuit experiment part:
(1). Adjustable DC stabilized power supply: 0~30V/1.5A continuously adjustable, automatic shifting, with automatic overload protection and self-recovery function.
(2). Fixed DC stabilized power supply: +5V/1A, ±12V/1A
(3). Function signal generator: wave form (sine wave, triangular wave, square wave), frequency range: 5Hz~550KHz continuously adjustable, output amplitude: sine wave more than 0-10Vp-p
(4). Frequency meter: measurement range: 1Hz~8MHz, 6-bit digital display, automatic shifting, input impedance ≥1MΩ/20PF, sensitivity
Measuring meter:
(1). Voltmeter: DC200V, class 0.5
(2). Ammeter: DC200mA, class 0.5
(3). Digital multimeter
Features : CHOIEO 66965101 112.602.000
• This trainer is suitable for courses such as 'PLC Technology', , 'Electric Appliance and PLC Control Technology' and 'PLC Application'.
• It is mainly composed of control panel, PLC mainframe, modular simulation modules and so on.
• The training table adopts plastic sprayed steel structure and designed with drawer, which is convenient for the storage of tools and modules. The table top is made up of high density board, with fireproof, waterproof and wearproof function.
• Frequency converter and motor can be added to extend the experiment content when needed. (optional)
• Safety protections: grounded, lead protection, safety in accordance with related GB standards. Insulated safety sockets, sheathed cables and wires.
TRAINING CONTENT
• PLC basic instruction training
• Motor forward and reverse control simulation
• Television transmitting tower simulation
• Traffic light control system simulation
• Automatic goods delivery and loading system simulation
• Automatic water tower water level control simulation
• Automatic molding machine system simulation
• Various liquids automatic control system simulation
• Automatic punching machine control system simulation
• Elevator control system simulation
• Automatic mail sorting system simulation
• Automatic washing machine control system simulation
• Plating control system simulation
• Automatic vending machine system simulation
• Relay control experiment
• Software simulation control
TECHNICAL PARAMETER
1. Input Voltage : AC 380V/220v, 50Hz 2. Temperature : -5~40°C, Below RH 90% 3. Overall power consumption: 0.3 kVA 4. Dimensions: table 1575mm×680mm×835mm (approx.) bench 1130mm×250mm×720mm (approx.) >BASIC CONFIGURATION 1. Training table: it adopts steel-wood material, with 16mm medium density fiberboard as the tabletop. The frame is made of rectangular steel tubes. The structure is designed with two drawers, PC cabinet, keyboard tray and lockable universal wheels.
2. Round stool (2pcs): Screw lifting range: 450~500mm, seat size: 300mm×300mm (approx.)
3. Control panel:
(1) AC power control unit: It is equipped with lighted fuse and leakage protection switch and provided with three phase 380V and single phase 220V power supply (one group each), which can be controlled by start-stop switches. Three-phase-four-wire AC 380V supply via air switch and can be monitored by voltmeter.
(2) Timer and alarm recorder: It has time setting, timing alarm, power cut-off function and can automatically record the electric leakage alarm time, which is caused by connection or operation.
(3) DC stabilized voltage: 0~30V adjustable, with rough/accurate adjust rotary knobs.
(4) DC constant current source: 0~200mA adjustable, with rough/accurate adjust rotary knobs.
(5) DC digital voltmeter: 0~200V, 10MΩ, class 0.5
(6) DC digital ammeter: 0~200mA, class 0.5
(7) Logic level output and indicator, self-locking/jog buttons
(8) Programmable logic controller: FX1N-40MR, 24I/16O, relay output
4. PLC simulation module (standard modular dimension 150mm×288mm×50mm)
(1) Motor positive and negative rotation control
(2) Television transmitting tower
(3) Traffic light control system
(4) Automatic goods delivery and loading system
(5) Automatic water tower water level control
(6) Automatic molding machine system
(7) Various liquids automatic control system
(8) Automatic punching machine control system
(9) Elevator control system
(10) Automatic mail sorting system
(11) Automatic washing machine control system
(12) Plating control system
(13) Automatic vending machine system
(14) Relay control experiment
5. Experiment wire: Length: 40cm/60cm/100cm, red/yellow/black, 60pcs in total.
6. PLC Programming software(copy): GX-Developer, It can accomplish the edit of PLC ladder diagram, instruction list, SFC,etc. The program can be saved as GPPQ, GPPA format.
7. Programmable cable: USB2.0 PC port, round head 8-pin PLC port, with 3 color LED communication indicator and driver disc (one-button type installation, available for windows XP, VISTA, WIN7, etc.).
8. Simulation software (copy): GX simulator.
9. PLC program: Programs for 14 simulation modules, 27 basic instructions, advanced instruction application
10. Power socket
Features : CHOIEO 66971105 136.771.500
• The electro pneumatic training platform is made up of experimental table, frame, pneumatic components, electrical control modules and so on.
• Modular structure design is adopted for experiment construction, each pneumatic component is an independent unit that comes with mounting baseboard. Reliable quick connectors are used for the connection of components.
• Aluminum alloy profile panel, with ‘T’ type mounting slot for pneumatic components installation and circuit construction. All solenoid valves, sensors and mircoswitches are designed with 4mm safety plug sockets for quick connection.
• The air compressor adopts air oil-less type compressor, which has the advantage of light weight, low power consumption and low noise.
• Safety protections: grounded, lead protection, safety in accordance with related GB standards. Insulated safety sockets, sheathed cables and wires.
TRAINING CONTENT
• Understanding of pneumatic structure and components
• Single acting cylinder manual reversing controlled loop
• 5/3 way solenoid directional valve controlled single acting cylinder loop
• 5/2 way single solenoid directional valve controlled single acting cylinder loop
• 5/2 way double solenoid directional valve controlled single acting cylinder loop
• Double acting cylinder hand directional valve control loop
• Double acting cylinder 5/2 way single solenoid directional valve control loop
• Double acting cylinder 5/2 way double solenoid directional valve control loop
• Single acting cylinder inching control loop
• Double acting cylinder inching control loop
• Sensor (capacitive/ photoelectric/ inductive) application control loop
• Dual pressure valve control loop
• Quick exhaust valve application control loop
• Sequence valve application control loop
• Time delay valve application control loop
• Four-cylinder linked action loop
• Double acting cylinder one-way speed regulation loop
• Double acting cylinder both-way speed regulation loop
> TECHNICAL PARAMETERS
1. AC power input: single phase AC220V±10%, 50Hz, 10A
2. Environment temperature: -10ºC~40 ºC Ambient humidity ≤ 85% (25 ºC)
3. Overall consumption: ≤ 2KVA
4. Working power supply: DC24V, 4.5A with short circuit protection function
5. Dimension: 1300mm×600mm×1700mm
6. Aluminum plate:1200mm×735mm (approx.)
PNEUMATIC COMPONENTS
1. Single acting cylinder (spring return) (Qty:1)
2. Double acting cylinder (Qty:3)
3. Air service unit (reduce valve/lubricator/filter) (Qty:1)
4. Reduce valve with pressure gage (Qty:1)
5. (5/2way) single solenoid valve (Qty:2)
6. (5/2way) double solenoid valve (Qty:1)
7. (5/2way) hand directional valve (Qty:1)
8. (3/2way) solenoid valve (Qty:1)
9. Air on/off valve (Qty:1)
10. (5/2way) double pneumatic valve (Qty:2)
11. (5/2way) single pneumatic valve (Qty:2)
12. Sequence valve (Qty:1)
13. Rotary cylinder (Qty:1)
14. Shuttle valve (Qty:2)
15. Dual pressure valve (Qty:1)
16. Time delay valve (Qty:1)
17. Quick exhaust valve (Qty:1)
18. One way valve (Qty:2)
19. Button valve (Qty:1)
20. Rotary valve (Qty:1)
21. Stroke valve (Qty:1)
22. Mushroom head button valve (Qty:1)
23. Throttle valve (Qty:6)
24. Capacitive sensor (Qty:4)
25. Photoelectric sensor (Qty:4)
26. Inductive sensor (Qty:4)
27. Magnetic reed switch suite (for cylinder) (Qty:1)
28. Microswitch (left trigger) (Qty:2)
29. Microswitch (right trigger) (Qty:2)
> ELECTRICAL CONTROL
1. Control panel board (1) High brightness aluminum-plastic panel (2) Size: 1200mm×735mm
2. Power part
(1) Six way DC 24V
(2) Three way single phase AC220V
(3) Leakage protective switch, emergency stop button, key on/off switch, main power indicator
3. Inching buttons
(1) 1NC/1NO inching button: 1 red, 2 green
(2) 1NO inching button: green
4. Self-locking rotary knobs: 1NC/1NO, two groups
5. Indicating light: 1 red, 1 green with connecting sockets
6. Relay part
(1) 3NO/3NC relay: 5-fold, with led indicators
(2) 1 timer relay, adjustable with delayed pick-up
(3) 1 timer relay, adjustable with delayed release
>ACCESSORIES
1. T-joint (Qty:10)
2. Cross joint (Qty:10)
3. Y-joint (Qty:10)
4. Air tube suite (Qty:1)
5. Tube plug (Qty:20)
6. Mounting base (Qty:5)
7. Air compressor:
(1) Motor power: 550W
(2) Rated current: 2.8A
(3) Input voltage: 220V, 50Hz
(4) Speed: 1380r/min
(5) Flow: 40L/min
(6) Capacity: 30L 8. Tools: straight screwdriver, scissors, nipper pliers, cross screwdriver, monkey wrench, sealing tape, socket head wrench
Features : CHOIEO 66971206 240.619.500
• This trainer is designed to meet the requirements for learning complex inner dynamic structure and working principle of hydraulic components.
• Independent relay control module is adopted for the electrical control of hydraulic system, which combines the transmission technology and control technology perfectly.
• The structure of transparent hydraulic component is designed according to real industrial hydraulic component, which is light in weight and small in size. Due to this, students can start or stop experiment in a short time.
• All the hydraulic components are equipped with quick installing baseboard and quick connecting joint to ensure convenient operation.
• Safety protections: grounded, lead protection, safety in accordance with related GB standards. Insulated safety sockets, sheathed cables and wires.
TRAINING CONTENT
• Function introduction and usage of hydraulic components
• Reversing loop of hand directional valve
• Lockout loop of median functional reversing valve
• Lockout loop of hydraulic controlled one-way valve
• Pressure setting loop
• Two-stage pressure loop
• Hydraulic loop of reducing valve
• Pressure boosting loop of pressure cylinder
• Unloaded loop of H-type reversing valve
• Oil in throttle speed regulating loop
• Oil return throttle speed regulating loop
• Reversing speed regulating loop of speed control gear pump
• Compound speed regulating loop of speed control gear pump and speed control valve
• Flow valve short connected speed changing-over loop
• Speed control valve series connected secondary feeding loop
• Sequential action loop of sequence valve
• Sequential action loop of pressure relay
• Sequential action loop of travel switch
• Sequential action loop of stroke valve
• Hydro-cylinder series connected synchronizing loop
• Reversing loop of pilot overflow valve
> TECHNICAL PARAMETERS
1. Input Voltage : Single-phase AC 220V, 50Hz , output DC24V/2A / 380Volt 50Hz
2. Temperature : -10~50ºC, Below RH 90%
3. Hydraulic oil pump motor: 250W, 0~1700r/min (with constant-voltage DC motor governor) maximum pressure: 2.5Mpa, required loop pressure: 0.5~1Mpa, voice less than 58dB (distance 1.5m)
4. Solenoid directional valve: 24V, suction: 30N
5. Dimensions: 1400mm×680mm×1760mm (approx.)
Electrical Control Part
1. Power supply and pump control unit
(1) RCCB with indicator
(2) Fuse protector
(3) Tachometer
(4) Speed regulator
(3) Oil flow control switch
2. Relay control unit (3-fold)
(1) Combined solenoid valve signal output socket
(2) Solenoid valve output signal indicators
(3) External reversing signal input sockets
(4) Internal reversing signal control buttons
3. Extended control unit
(1) DC24V power supply with indicator
(2) Sensor signal acquisition part
(3) Button control unit, 1NC/1NO (two groups)
(4) Relay control unit, 1NC/1NO (two groups)
> Hydraulic Pump Station
1. Permanent magnet DC motor: 220V, 250W, 1.2A, 1700r/min
2. Hall switch: NPN, NO, 50mA, 10mm
3. Gear pump: 1450r/min
4. Pressure gauge: -0.1-1.6MPa
5. Overflow valve
6. Transparent oil tank with filling hole
7. Filter 8. Motor and pump suspension plate
Accessories :
1. Travel switches and sensors
2. Tool kit
3. Cables
(1) Capacitive sensor (Qty:2)
(1). Straight screwdriver
(1). Solenoid valve cable
(2) Inductive sensor (Qty:2)
(2). Cross screwdriver
(2). Pressure relay cable
(3) Photoelectric sensor (Qty:2)
(3). Monkey wrench
(3). General connecting cable
(4). Needle nose pliers
(5). External circlip pliers
(6). Internal circlip pliers
(4) Travel switch (N/O) (Qty:2)
(7). Socket head wrench suite
(5) Travel switch (N/C) (Qty:2)
(8). Portable tool box
Untuk
pemesanan atau informasi silahkan hubungi alamat kontak kami :
CV.ASAKA PRIMA | DUTA MEDIA GROUP.
PERCETAKAN & DISTRIBUTOR ALAT LAB & PERAGA PENDIDIKAN.
Jl.Maulana Hasanudin No.52 Cipondoh - Kota Tangerang
PERCETAKAN & DISTRIBUTOR ALAT LAB & PERAGA PENDIDIKAN.
Jl.Maulana Hasanudin No.52 Cipondoh - Kota Tangerang
Cabang : Ruko Pondok Permata No.1, Jl.
Raya Tanggul, Rajeg Mulya, Rajeg, Tangerang, Banten 15540
021 5570 1397
021 5570 2265
0813.1019.7873
WA.0812.1236.8589
WA.0877.7432.4146
0813.8053.7399
www.asakaprima.net
asakaprima@gmail.com
021 5570 1397
021 5570 2265
0813.1019.7873
WA.0812.1236.8589
WA.0877.7432.4146
0813.8053.7399
www.asakaprima.net
asakaprima@gmail.com
